开槽螺母-螺栓连接副拧紧特性研究*

doi:10.16731/j.cnki.1671-3133.2024.06.016

现代制造工程 ›› 2024, Vol. 525 ›› Issue (6): 122-127.doi: 10.16731/j.cnki.1671-3133.2024.06.016

开槽螺母-螺栓连接副拧紧特性研究^*

李坤^1,2, 刘龙权^1,2

1 上海交通大学航空航天学院,上海 200240;
2 上海交通大学民机结构强度综合实验室,上海 200240

收稿日期:2023-10-31 出版日期:2024-06-18 发布日期:2024-07-02
通讯作者: 刘龙权,博士,教授,主要研究方向为航空结构机械连接和胶接结构制造、纤维增强复合材料结构强度分析和损伤容限设计。E-mail:liulongquan76@sjtu.edu.cn
作者简介:李坤,硕士研究生,主要研究方向为飞机结构强度。E-mail:chuc0403@sjtu.edu.cn
基金资助:
*国家自然科学基金项目(52075326)

A research on tightening characteristics of slotted nut-bolt connection pair

LI Kun^1,2, LIU Longquan^1,2

1 School of Aeronautics and Astronautics, Shanghai Jiao Tong University, Shanghai 200240, China;
2 Lab of Civil Aircraft Structural Testing, Shanghai Jiao Tong University, Shanghai 200240, China

Received:2023-10-31 Online:2024-06-18 Published:2024-07-02

摘要/Abstract

摘要： 由于飞机飞行过程持续遭受振动载荷,设计中广泛采用具有自锁功能的开槽螺母-螺栓连接副以防螺栓的松动和夹紧力损失。研究开槽螺母-螺栓连接副的拧紧特性,对保证连接结构的力学性能、安全性和可靠性具有重要意义。对开槽螺母拧紧工艺开展了理论分析,修正了其夹紧力-拧紧力矩关系公式。试验研究了开槽螺母型号、被连接件材料、润滑条件以及重复拧紧次数等条件对拧紧特性的影响。研究结果表明,NASM14144开槽螺母相较于高度较低的NASM14145开槽螺母,预置力矩提升了125.9 %,而扭矩系数稍有降低;饱和润滑方式能有效降低扭矩系数及其波动性,螺母-连接板贴合面润滑的效果次之;重复拧紧过程使得NASM14144螺母的预置力矩降低、扭矩系数明显升高,而NASM14145螺母的拧紧特性并未显著改变。

关键词: 拧紧过程, 开槽螺母, 预置力矩, 夹紧力, 复合材料

Abstract: Since the aircraft is continuously subjected to vibratory loads during flight process,the self-locking slotted nut-bolt connection pair is widely used in design to prevent loosening of the bolt and loss of clamping force.Studying the tightening characteristics of the slotted nut-bolt connection pair is of great significance for ensuring the mechanical performance,safety,and reliability of the connected structure.Theoretical analysis was conducted on the tightening process of the slotted nut,and the clamping force-tightening torque relationship formula was corrected.The influence of factors such as slotted nut type,connected material,lubrication conditions,and repeated tightening times on tightening characteristics was investigated through experiments.The results show that the prevailing torque of NASM14144 slotted nut is increased by 125.9 % and the torque coefficient is slightly decreased compared with the lower NASM14145 slotted nut.Torque coefficient and its fluctuation can be effectively reduced by saturated lubrication method,and lubrication of the nut-plate bonding surface is less effective.In the process of repeated tightening,the prevailing torque of NASM14144 nut was reduced and the torque coefficient was significantly increased,while the tightening characteristics of NASM14145 nut did not change significantly.

Key words: tightening process, slotted nut, prevailing torque, clamping force, composite material

中图分类号:

V229+.1

李坤, 刘龙权. 开槽螺母-螺栓连接副拧紧特性研究^*[J]. 现代制造工程, 2024, 525(6): 122-127.

LI Kun, LIU Longquan. A research on tightening characteristics of slotted nut-bolt connection pair[J]. Modern Manufacturing Engineering, 2024, 525(6): 122-127.

参考文献

[1] SUN Q C,LIN Q Y,YANG B,et al.Mechanism and quantitative evaluation model of slip-induced loosening for bolted joints[J].Assembly Automation,2020,40:77-88.
[2] GONG H,LIU J H,DING X,et al.Calculation of the effective bearing contact radius for precision tightening of bolted joints[J].Advances in Mechanical Engineering,2016,8(9):1-8.
[3] 张明远.基于螺纹面磨损的螺栓松动寿命仿真预测方法研究[D].成都:西南交通大学,2019.
[4] CNN.Loose nut costs Air Force $62.4 million in accident[EB/OL].(2015-08-28)[2023-10-23].https://edition.cnn.com/2015/08/27/politics/loose-nut-air-force-crash/index.html.
[5] 蔡跃波,安鲁陵,王楚凡,等.螺栓拧紧过程中工况对复合材料连接结构夹紧力的影响[J].复合材料学报,2022,39(2):812-822.
[6] 李维荣.螺纹紧固件防松技术和试验方法研究[D].合肥:合肥工业大学,2005.
[7] 巩浩,刘检华,冯慧华,等.螺纹连接松动机理和防松方法研究综述[J].机械工程学报,2022,58(10):326-347.
[8] HAN N,AN L L,FAN L X,et al.Research on temperature field distribution in a frame mold during auto-clave process[J].Materials,2020,13:4020.
[9] 张京东,邓博,桂学文,等.高锁螺母收口、装配及松动过程有限元分析[J].中国机械工程,2023,34(12):1387-1394.
[10] OH J H,KIM Y G.Optimum bolted joints for hybrid composite materials[J].Composite Structures,1997,38(1/2/3/4):329-341.
[11] MOTOSH N.Development of Design Charts for Bolts Preloaded up to the Plastic Range[J].Journal of Engineering for Industry,1976,98(3):849-851.
[12] 《近海风电场关键技术建设手册》编制小组.海上风电螺纹连接的拧紧力矩计算方法分析[J].风能,2011(6):66-68.
[13] DEAN S W,REIFF J D.A Procedure for Calculation of Torque Specifications for Bolted Joints with Prevailing Torque[J].Journal of ASTM International,2005,2(3):1-8.
[14] YU Q,YANG X,ZHOU H.An experimental study on the relationship between torque and preload of threaded connections[J].Advances in Mechanical Engineering,2018,10(8):1-10.
[15] 周春华.螺栓预紧精度及预紧可靠性分析[J].长沙铁道学院学报,1996(3):58-63.
[16] FRIEDRICJ C,HUBBERTZ H.Engineering calculation of threaded fastening systems considering deviations in advanced design[C]//ASME International Mechanical Engineering Congress and Exposition.[S.l.]:American Society of Mechanical Engineers,2012:865-871.

开槽螺母-螺栓连接副拧紧特性研究^*

A research on tightening characteristics of slotted nut-bolt connection pair

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

[1]	邱雯, 张帆, 谭跃刚, 张俊, 涂一文. 基于主应力轨迹线的连续碳纤维复合材料3D打印路径规划方法[J]. 现代制造工程, 2024, 525(6): 22-27.
[2]	李伟豪;茅健;郑武;张婷. 四足机器人腿部结构拓扑优化设计及力学性能分析[J]. 现代制造工程, 2023, 516(9): 45-53.
[3]	李恒;邱睿;周甘华;曹清林;刘锦程. 纤维增强复合材料汽车前防撞梁的设计与分析[J]. 现代制造工程, 2023, 514(7): 79-88.
[4]	李伟豪，茅健，郑武，张婷. 基于拓扑优化的多复合材料3D打印增强方法及实验研究[J]. 现代制造工程, 2023, 513(6): 26-32.
[5]	武方超，雷小宝，谢峰. 切削SiCp/Al复合材料的切屑形成及颗粒损伤仿真分析[J]. 现代制造工程, 2023, 512(5): 91-100.
[6]	卢强;沈琴;刘钢;王晓玮;黄道柱. 碳纤维铝蜂窝复合材料汽车保险杠横梁轻量化设计[J]. 现代制造工程, 2023, 510(3): 77-82.
[7]	龙海波，毕庆贞. 基于可变形带的碳纤维增强树脂基复合材料3D打印[J]. 现代制造工程, 2022, 502(7): 18-24.
[8]	吴春岳，程祥，薛冰，刘原勇，郑光明，李阳. 三明治复合材料机械结构分析[J]. 现代制造工程, 2022, 502(7): 90-96.
[9]	王金宇，游珠杰，辛泰阿，宋世彬，邵一川. 碳纤维增强复合板钻削工艺的有限元建模研究[J]. 现代制造工程, 2021, 492(9): 68-76.
[10]	曹汉，张秋菊. 连续碳纤维增强复合材料3D打印机剪丝机构设计[J]. 现代制造工程, 2021, 490(7): 10-15.
[11]	许明阳, 殷晨波, 陈曦. 碳纤维布胶接修复含裂纹钢管仿真分析[J]. 现代制造工程, 2021, 484(1): 142-146.
[12]	韩启超,赵启林. 复合材料传动轴智能优化设计[J]. 现代制造工程, 2020, 477(6): 37-45.
[13]	孙安娜，何涛，霍元明，东星倩，王京. 304不锈钢/TiNi纤维对增强ZL105A复合材料组织和性能的影响[J]. 现代制造工程, 2020, 473(2): 104-109.
[14]	姚婷婷，何涛，王京，霍元明，高建烨. SiC纳米颗粒表面处理方式对增强铝基复合材料组织和性能的影响[J]. 现代制造工程, 2020, 483(12): 1-5.
[15]	韩启超,施丽铭,马森,邓宇华,盛聪,赵启林,姚远明. 基于差分进化算法的复合材料铝蜂窝夹芯筒优化设计[J]. 现代制造工程, 2020, 481(10): 134-142.