梯度自润滑陶瓷刀具干切削不锈钢的试验研究

doi:10.16731/j.cnki.1671-3133.2017.10.019

现代制造工程 ›› 2017, Vol. 445 ›› Issue (10): 102-105.doi: 10.16731/j.cnki.1671-3133.2017.10.019

梯度自润滑陶瓷刀具干切削不锈钢的试验研究

于俊飞^1,2, 衣明东^1,2, 吴光永³, 许崇海^1,2

1 齐鲁工业大学机械与汽车工程学院,济南 250353;
2 齐鲁工业大学山东省高校轻工装备先进制造与测控技术重点实验室,济南 250353;
3 山东大学机械工程学院,济南 250061

收稿日期:2015-11-10 出版日期:2017-10-20 发布日期:2018-01-08
作者简介:于俊飞,硕士研究生,主要研究方向为先进工模具及其加工与控制技术。 E-mail:junfeiyu@126.com

Experimental study of gradient self-lubricating ceramic tool when dry cutting stainless steel

Yu Junfei^1,2, Yi Mingdong^1,2, Wu Guangyong³, Xu Chonghai^1,2

1 School of Mechanical and Automotive Engineering,Qilu University of Technology,Jinan 250353,China;
2 Key Laboratory of Advanced Manufacturing and Measurement and Control Technology for Light Industry in Universities of Shandong,Qilu University of Technology,Jinan 250353,China;
3 School of Mechanical Engineering,Shandong University,Jinan 250061,China

Received:2015-11-10 Online:2017-10-20 Published:2018-01-08

摘要/Abstract

摘要： 通过正交试验,研究分析Al₂O₃/(W,Ti)C/CaF₂梯度自润滑陶瓷刀具切削304奥氏体不锈钢(0Cr18Ni9)时切削要素(切削速度、进给量及切削深度)对三向切削力的影响规律;利用正交表进行方差分析及F检验,得到三个影响因素的主次次序和影响显著性;利用指数回归分析建立陶瓷刀具主切削力的经验公式。试验结果表明,在给定的切削参数范围内,存在主切削力小于背向力的情况;F检验结果表明进给量和切削深度对主切削力有显著影响,而切削速度对主切削力的影响不显著;主切削力和背向力均随着进给量和切削深度的增加而升高。

关键词: 梯度自润滑陶瓷刀具, 奥氏体不锈钢, 切削力, 回归分析

Abstract: By means of orthogonal experiment,the effect of cutting factors(cutting speed,feed rate,depth of cut) on cutting forces is studied when dry cutting 304 austenitic stainless steel (0Cr18Ni9) with Al₂O₃/(W,Ti) C/CaF₂ gradient self-lubricating ceramic tool.Orthogonal table is used to perform the analysis of variance and F-test to confirm the primary and second order and significant influence of cutting parameters on cutting forces;empirical formula of main cutting force is established by exponential regression analysis.It can be indicated that main cutting force may be smaller than radial force in given range of cutting parameters.The result shows from F-test that feed rate and depth of cut have significant effect on cutting force.Main cutting force and radial force increase with the increasing feed rate and depth of cut.

Key words: gradient self-lubricating ceramic tool, austenitic stainless steel, cutting force, regression analysis

中图分类号:

TG506.7

于俊飞, 衣明东, 吴光永, 许崇海. 梯度自润滑陶瓷刀具干切削不锈钢的试验研究[J]. 现代制造工程, 2017, 445(10): 102-105.

Yu Junfei, Yi Mingdong, Wu Guangyong, Xu Chonghai. Experimental study of gradient self-lubricating ceramic tool when dry cutting stainless steel[J]. Modern Manufacturing Engineering, 2017, 445(10): 102-105.

参考文献

[1] 陈日曜.金属切削原理[M].北京:机械工业出版社,2002:124-126.
[2] 刘志峰,张崇高,任家隆.干切削加工技术及应用[M].北京:机械工业出版社,2005.
[3] XU C H,WU G Y,XIAO G C,et al.Al₂O₃/(W,Ti)C/CaF₂ Multi-component Graded Self-lubricating Ceramic Cutting Tool Material[J].International Journal of Refractory Metals and Hard Materials,2014(45):125-129.
[4] XU Xiuguo,XU Chonghai,FANG Bin,et al.Preparation of TiB₂/WC/h-BN Micro-nano Composite Gradient Self-lubricating Ceramic Tool Material[J].Key Engineering Materials,2013(589/590):307-311.
[5] SENTHIL Kumar A,RAJA Durai A,SORNAKUMAR T.Wear Behavior of Alumina Based Ceramic Cutting Tools on Machining Steels [J].Tribology International,2006(39):191-197.
[6] SENTHIL Kumar A,RAJA Durai A,SORNAKUMAR T.The Effect of Tool Wear on Tool Life of Alumina-based Ceramic Cutting Tools While Machining Hardened Martensitic Stainless Steel[J].Journal of Materials Processing Technology,2006(173):151-156.
[7] KEHINDE Sobiyi,IAKOVOS Sigalas,GUVEN Akdogan,et al.Performance of Mixed Ceramic and CBN Tools During Hard Turning of Martensitic Stainless Steel[J].International Journal of Advanced Manufacturing Technology,2015(77):861-871.
[8] DEARNLEY P A,THOMPSON V.Evaluation of Failure Mechanisms of Ceramics and Coated Carbides Used for Machining Stainless Steels[J].Surface Engineering,1986,2(3):191-202.
[9] DENG Jianxin,LIU Lili,YANG Xuefeng,et al.Self-lubrication of Al₂O₃/TiC/CaF₂ Ceramic Composites in Sliding Wear Tests and in Machining Processes[J].Materials and Design,2007(28):757-764.
[10] DENG Jianxin,CAO Tongkun,YANG Xuefeng,et al.Self-lubrication of Sintered Ceramic Tools with CaF2 Additions in Dry Cutting [J].International Journal of Machine Tools & Manufacture,2006(46):957-963.
[11] DENG Jianxin,CAO Tongkun,LIU Lili.Self-lubricating Behaviors of Al₂O₃/TiB₂ Ceramic Tools in Dry High-speed Machining of Hardened Steel[J].Journal of the European Ceramic Society,2005(25):1073-1079.
[12] 衣明东.纳米固体润滑剂与梯度设计协同改性陶瓷刀具的研究[D].济南:山东大学,2014:115-118.
[13] YI Mingdong,XU Chonghai,CHEN Zhaoqiang,et al.Preparation of Al₂O₃ Based Nano-micro Composite Gradient Self-lubricating Ceramic Tool Materials[J].Materials Science Forum,2014(788):613-616.
[14] 衣明东,许崇海,陈照强,等.纳米CaF₂对自润滑陶瓷材料力学性能的影响[J].硅酸盐学报,2014,42(9):1127-1133.
[15] 戴登钊,周后明,祝贺,等.陶瓷刀具切削奥氏体不锈钢的切削力试验研究[J].机械设计与制造,2012(12):252-254.
[16] YIN Zengbin,HUANG Chuanzhen,YUAN Juntang,et al.Cutting Performance and Life Prediction of an Al₂O₃/TiC Micro-nano-composite Ceramic Tool When Machining Austenitic Stainless stel[J].Ceramics International,2015(41):7059-7065.
[17] BASAVARAJAPPA S,SURESH R,GAITONDE V N,et al.Analysis of Cutting Forces and Surface Roughness in Hard Turning of AISI 4340 using Multilayer Coated Carbide Tool [J].Machining and Machinability of Materials,2014,16(2):169-185.
[18] 章锦华.精密切削理论与技术[M].上海:科学技术出版社,1986:32-35.

梯度自润滑陶瓷刀具干切削不锈钢的试验研究

Experimental study of gradient self-lubricating ceramic tool when dry cutting stainless steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 12

编辑推荐

Metrics

[1]	张冬冬，苏宇. 纳米流体同轴静电雾化切削荷电与加工性能研究[J]. 现代制造工程, 2022, 498(3): 1-5.
[2]	傅萍，胡博，于润桥，姜禹桐. 基于盲源分离的304奥氏体不锈钢弱磁信号处理[J]. 现代制造工程, 2021, 491(8): 125-131.
[3]	马成庆，高长水，刘壮，胡丹，屈中垚，田建川，毛光华. 汽车内饰装配线小时产出及设备使用率优化研究[J]. 现代制造工程, 2020, 474(3): 21-25.
[4]	王栋梁，窦建明，彭文，张红梅. 轴向超声振动车削液压滑阀阀芯的试验研究[J]. 现代制造工程, 2020, 472(1): 97-101.
[5]	赵慧娟, 解欢. 刀具坐标系铣削力建模及系数识别方法[J]. 现代制造工程, 2019, 460(1): 108-111.
[6]	燕芸, 张满栋. 电镀CBN硬珩齿加工过程分析及齿面优化[J]. 现代制造工程, 2019, 460(1): 117-120.
[7]	都金光,张海振,马军,明五一,何文斌. 单颗粒金刚石加工SiCp/Al复合材料的仿真与实验研究[J]. 现代制造工程, 2018, 455(8): 11-15.
[8]	任利伟,焦锋,牛赢. 淬硬模具钢超声辅助铣削力的试验研究[J]. 现代制造工程, 2018, 455(8): 69-74.
[9]	唐林虎, 沈浩, 常青山, 阴俊, 林小军. 低中高速干式硬态车削高硬高强高耐磨淬硬钢的试验研究[J]. 现代制造工程, 2018, 451(4): 1-5.
[10]	刘国跃, 周志雄, 贾寓真, 刘刚. 双金属带锯条齿距与切削力关系研究[J]. 现代制造工程, 2018, 459(12): 103-106.
[11]	段鹏, 焦锋, 赵波, 牛赢. 激光超声复合加工硬质合金的切削力理论与试验[J]. 现代制造工程, 2017, 446(11): 9-14.
[12]	周春雷. 本构模型参数对切削过程仿真影响的研究[J]. 现代制造工程, 2017, 436(1): 105-109.